Відео

Cant get it work.. left door

There is a cotter pin on the large spring of the Bowden cable that holds the spring back. Does this cotter pin have to be removed after installing the window regulator mechanism?

Does it have to bo even on that roll ?

y se debe soltar al final la chapita blanca que retiene el muelle para que quede tenso total

Gros merci ça m'a super aidé pour refaire mon lève vitre

Not easy it took me hour and a half not fun glad it's finished.

be careful as this is not the left door on a RHD car. Process is correct bur check cables are connectedin relation to the feet of the runners. I also had to adjust the sheath lenth on the longest cable to get enough slack to work

Are you sure this is correct as I can’t get the spool back in as you show as there are two springs in the white housings that slot into the motor plate. Am I missing something?

Great videos

Right hand ?

Alguien sabe las medidas de los cables??

Good men

Un completo lio. Por 10€ más comprar uno nuevo o de segunda montado

I cannot fit in the cable it is too short what can I do about it

Mate I have tried this part 4:08 about 20 times it keeps piping out of place when I put it up to the metal bit to put it on god knows why could you please add me on face book or anything and tell me what I’m doing wrong

Thanks for video

Y

It’s sad this is the only video that could help us and u didn’t even say a single word that’s great haha

👍👍👍👍🎉🎉🎉

Thanks 🙏🏻🙏🏻🙏🏻

Спасибо этому видео !!!! Я три дня голову ломал

Пружинок не поставили)))) как и я ))))

походу гимор еще тот!у меня порвался трос-то что на видео это непонятка полная!

Hi, I have same problem for my car do you can fixed?

Is this the same as the jetta 3 passat

this is not the "left" side window regulator - this is the right side assembly! I have been looking at this video and comparing it against assemblies I have in stock and when I assembled one using the rails you have pictured it ends up being the passenger side and not the driver side! I assembled a driver side using this video and the whole mechanism is backwards! You need to reshoot this video with the correct rails! :(

jb

Hello there were was the repair wire's bought my 407 coupe is the same design so would like to have a spare just in case thanks John

It's much easier to just buy a new motor with regulator for $50 that is ready to be attached to the window

You must be German

Thanks! But you forgot the springs man

Merci beaucoup pour vos vidéos. à la suite des opérations ( avec qqs erreurs de manipulation ) sur lève-vitre Xsara Picasso, j'entends un bruit de relais ( à côté de la portière) et puis impossible à démarrer. Qqn a une idée d'où cela provient et où se trouve le relais? Merci

What bout 307cc

Ok, I did get there, Can I just add at the final point of getting the wheel on its mount with both wires tight and in their groves, you will need to turn it over and rotate it at the same time, rotate to tighten wires.Helpful vid thanks

Great video, no hello you tubers BS, Just a simple step by step instructional video. Thank you for that. The other video that came up when researching this, had a guy that just talked way too much and represented his channel heavily. (which isn't bad, I just wasn't in the mood for all that extra pep) I appreciate you for making this video. Thank You..

should have filmed a bit longer

Hello , how to remove rope fitting from the slot?

Precious video. Thank you. Greetings from Portugal.

Danke ☺

Do you have any regulators for the 306 cab? Front and rear?

Hello, what to do if wire is broken ? And motor is working fine ?

Hello Where can i buy a front right window cable by Peugeot 306 1996 Cabrio Please tell me Thank you advance

Hello and thank you for your video but I do not see how you fix the white strip, I mean in what direction because on your film we do not see sufficiently this level. Can you at help me so I know how to fix it? Thank you

На кой перчатки со бля хирург что ли

This seems back to front

Thanks,this is very useful video ,now I can do it myself.

2 mistakes 1. The metal bar with the 3 plastik clips Have to be on the back site so the 2 holes for the screw look at you 2. The short side hast to be wrapped an the other side

its right window regulator(passenger), not left...

The link you have in the description comes up with an error message - do you have another supplier for the driver side regulator repair kit?

the video is ok, but no information how to slide the glass back into position :D